ICL, ICL Datasheet, ICL 3 1/2 Digit LCD Display, buy ICL The Maxim ICL and ICL are monolithic analog . descriptive excerpts from the original manufacturer’s data sheet have been included in this data. ICL datasheet, ICL circuit, ICL data sheet: INTERSIL – 3 1/2 Digit, LCD/LED Display, A/D Converters,alldatasheet, datasheet, Datasheet search.

Author: Taurr Bagami
Country: Mexico
Language: English (Spanish)
Genre: Love
Published (Last): 15 October 2013
Pages: 400
PDF File Size: 20.36 Mb
ePub File Size: 20.24 Mb
ISBN: 550-3-92969-452-9
Downloads: 25230
Price: Free* [*Free Regsitration Required]
Uploader: Vule

While other types of capacitors are adequate for this application, polypropylene capacitors give undetectable datsaheet at reasonable cost. Submit Document Feedback 7 FN Two basic clocking arrangements can be used: Submit Document Feedback 16 FN The analog input required to generate full scale output counts is: For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.

This is because over-range is a low dissipation mode, with the three least significant digits blanked.

The input signal can be referenced to the center of the common mode range of the converter. Third, a feedback loop is closed around the system to charge the auto-zero capacitor CAZ to compensate for offset voltages in the buffer amplifier, integrator, and comparator.

This differential voltage can be datasehet a wide common mode range: Direct drive with digital logic supply amplitude. Deintegrate Phase The final phase is datasheeg, or reference integrate.


It is then further divided to form the three convert-cycle phases. October 24, FN All these problems are of course eliminated if an external reference is used.

On the 2V scale, a 0.

An additional requirement of the integrating capacitor is that it must have a low dielectric absorption to prevent roll-over errors. Finally, the true economy of single power supply operation ICLenables a high performance datadheet meter to be built with the addition of only 10 passive components and a display. Dimensions D1 and E1 do not include mold protrusion. Specifically the digital reading displayed is: In this application, analog COMMON should be tied to the same point, thus removing the common mode voltage from the converter.

Allowable protrusion is 0. About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. However, by selecting the reference capacitor such that it is large enough in comparison to the stray capacitance, dataseet error can be held to less than 0.

Datasheets search archive of electronic components datasheets

Please refer to TB for details on reel specifications. The oscillator frequency is divided by four before it ico7106 the decade counters. They are not intended for use in Reflow solder processing applications. D, D1, and E1 dimensions il7106 not include mold flash or protrusions. ICL is tested in the circuit of Figure 2. For information regarding Intersil Corporation and its products, see www. Second, the reference capacitor is charged to the reference voltage.


This difference in reference for positive or negative input voltage will give a roll-over error. Included are seven segment decoders, display drivers, a reference, and a clock.

Information furnished idl7106 Intersil is believed to be accurate and reliable. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders.

ICL, ICL, ICLS Datasheet

Due to their higher thermal resistance, plastic parts are poorer in datashedt respect than ceramic. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. At the end of this phase, the polarity of the integrated signal is determined.

The integrating resistor should be large enough to remain in this very linear region over the input voltage range, but small enough that undue leakage requirements are not placed on the PC board.